Difference between revisions of "Main Page"

From NaplesPU Documentation
Jump to: navigation, search
(Simulate a kernel)
(Simulate a kernel)
Line 33: Line 33:
 
* starting simulate.sh from a root folder of repository, if simulator software chosen is ModelSim.
 
* starting simulate.sh from a root folder of repository, if simulator software chosen is ModelSim.
  
First of all, is needed to load Vivado or ModelSim function in the shell by source command. This step is mandatory for all ways. In Ubuntu Linux environment, if simulator software chosen is Vivado, it can be possible by launching the following command:
+
First of all, is needed to load Vivado or ModelSim function in the shell. This step is mandatory for all ways. In Ubuntu Linux environment, if simulator software chosen is Vivado, it can be possible by launching the following command:
  
 
<code>$ source Vivado/folder/location/settingXX.sh</code>
 
<code>$ source Vivado/folder/location/settingXX.sh</code>

Revision as of 07:13, 3 April 2019

TODO: project overview here

Getting started

This section shows how to approach with nu+ project for simulating or implementing a kernel for nu+ architecture.

Required software

Simulation or implementation of any kernel relies on the following dependencies:

  • Git
  • Xilinx Vivado 2018.2 or lower or ModelSim
  • nu+ toolchain

Building process

First step is to obtain the source code of nu+ architecture from official repository by cloning a repository from [1]

In Ubuntu Linux environment, this step is fulfilled by starting following command:

$ git clone 'https://gitlab.com/vincenscotti/nuplus'

In nu+ repository, toolchain consist in a sub-module of repository, so is needed to update. In Ubuntu Linux environment, just type the following command in a root folder of repository:

$ git submodule update --init

Then, third step is to install a toolchain. This process is described [here].

At this point, in a root folder of repository, there are a few sub-folder. Two of this sub-folder are of particular interest for the purpose:

  • software, where are stored all kernels (in a sub-folder kernel);
  • tools, where are stored all scripts for simulate one or more kernel.

Simulate a kernel

For simulate a kernel there are three way:

  • starting test.sh script
  • starting setup_project.sh from a root folder of repository, if simulator software chosen is Vivado;
  • starting simulate.sh from a root folder of repository, if simulator software chosen is ModelSim.

First of all, is needed to load Vivado or ModelSim function in the shell. This step is mandatory for all ways. In Ubuntu Linux environment, if simulator software chosen is Vivado, it can be possible by launching the following command:

$ source Vivado/folder/location/settingXX.sh

where XX depend on installed version of Vivado (32 o 64 bit).

If simulator software chosen is ModelSim, is needed to add environment variable of ModelSim to PATH variable and load a license in the shell. In Ubuntu Linux environment, the commands to launch is:

$ export PATH=$PATH:ModelSim/folder/location/bin/ $ export LM_LICENSE_FILE=1717@vlsi2:$LM_LICENSE_FILE

test.sh script

For start test.sh script, type following command with some options in a nuplus/tools folder:

$ ./test.sh [option]

Options that can be use are:

  • -h, --help show this help
  • -t, --tool=vsim or vivado specify the tool to use, default: vsim
  • -cn, --core-numb=VALUE specify the core number, default: 1
  • -tn, --thread-numb=VALUE specify the thread number, default: 8

This script allows to start one or more kernel defined in an array of script. The test.sh script provide to compile kernels and run them on nu+ and x86 architecture. Once simulation is terminated, for each kernel, results of both execution are compared by a Python script for verifying correctness of result of nu+ architecture.

In folder tools there is a log file, called cosim.log, where are stored some information about simulation.

setup_project.sh script

For start setup_project.sh script, type following command with some options in a nuplus folder:

$ tools/vivado/setup_project.sh [option]

Options that can be use are:

  • -h, --help show this help
  • -k, --kernel=KERNEL_NAME specify the kernel to use
  • -s, --single-core select the single core configuration, by default the manycore is selected
  • -c, --core-mask=VALUE specify the core activation mask, default: 1
  • -t, --thread-mask=VALUE specify the thread activation mask, default FF
  • -m, --mode=gui or batch specify the tool mode, it can run in either gui or batch mode, default: gui

This script allow to start a kernel specified in a command. Kernel will compile and run on nu+ architecture. Simulation is performed by Vivado.

simulate.sh script

For start simulate.sh script, type following command with some options in a nuplus folder:

$ tools/modelsim/simulate.sh [option]

Options that can be use are:

  • -h, --help show this help
  • -k, --kernel=KERNEL_NAME specify the kernel to use
  • -s, --single-core select the single core configuration, by default the manycore is selected
  • -c, --core-mask=VALUE specify the core activation mask, default: 1
  • -t, --thread-mask=VALUE specify the thread activation mask, default FF
  • -m, --mode=gui or batch specify the tool mode, it can run in either gui or batch mode, default: gui

This script allow to start a kernel specified in a command. Kernel will compile and run on nu+ architecture. Simulation is performed by ModelSim.

Implement a kernel

TODO: creazione, compilazione



TODO: clone repository, struttura cartelle

... then you can simulate or implement the system on a supported board...

Documentation

The nu+ Hardware Architecture

The nu+ Toolchain

The nu+ Instruction Set Architecture

The nu+ Emulator TODO: da rimuovere?

TODO Writing nu+ applications: spiegazione workflow kernel, scrittura-compilazione-file generati (altrove sara' spiegata la simulazione e il loading su scheda)

Example of nu+ applications TODO spostare contenuti in una sezione "Examples" da includere nella pagina di sopra

Deeping in nu+ aspects

nu+ HowTo

Progetto di Tile Eterogenea TODO: spostare altrove

Contributing to nu+ TODO: spostare i contenuti marcati come tali nel wiki

Further information on MediaWiki

TODO: da rimuovere/salvare altrove

The nu+ project documentation will be based on MediaWiki. For information and guides on using MediaWiki, please see the links below: